How To Change An Iphone 5 Battery

Introduction

Bring life back to your iPhone 5 with a new battery. If your battery is swollen, take advisable precautions.

This guide instructs you lot to disassemble the front panel associates; this is intended to forbid harm to the brandish cables. If you lot feel comfy supporting the display carefully while peeling the battery out of the body, skip the brandish removal (steps thirteen-sixteen) and go to the battery removal steps.

For optimal functioning, after completing this guide, calibrate your newly installed bombardment: Accuse it to 100% and keep charging it for at least two more hours. Then apply your iPhone until information technology shuts off due to depression battery. Finally, charge information technology uninterrupted to 100%.

You can also use this guide to supercede the bombardment connector subclass.

Video Overview

• If your display glass is cracked, go on further breakage contained and forbid bodily damage during your repair by taping the drinking glass.

• Lay overlapping strips of clear packing record over the iPhone's brandish until the whole face is covered.

• This volition keep drinking glass shards independent and provide structural integrity when prying and lifting the display.

• Clothing prophylactic glasses to protect your eyes from any glass shaken complimentary during the repair.



• Before you proceed, discharge your iPhone battery below 25%. A charged lithium-ion bombardment can catch fire and/or explode if accidentally punctured.

• Power off your iPhone before beginning disassembly.

• Remove the two three.6 mm Pentalobe screws side by side to the Lightning connector.

• In the following steps you will exist pulling the brandish up out of the telephone body. The display is equanimous of a drinking glass screen and a plastic bezel with metallic clips.

• Regardless of the tool you use, you need to be sure y'all pull up the entire brandish.

• If the glass begins to dissever from the plastic, as shown in the get-go paradigm, slide a plastic opening tool between the plastic frame and the metal phone trunk to pry the metal clips out of the case.

• If you are reassembling a telephone with a separated display bezel, you may want to identify a thin strip of agglutinative between the plastic bezel and the glass to keep the phone closed.

• The next two steps demonstrate using the iSclack, a bully tool for safely opening the iPhone 5 that we recommend for anyone doing more than than one repair. If y'all aren't using the iSclack, skip to Pace 6.

• Close the handle on the iSclack, opening the suction-cup jaws.

• Identify the bottom of your iPhone in between the suction cups, against the plastic depth gauge.

• The top suction loving cup should rest only above the home button.

• Open the handles to close the jaws of the iSclack. Middle the suction cups and printing them firmly onto the pinnacle and lesser of the iPhone.

• Concur onto your iPhone securely and close the handle of the iSclack to split the suction cups, pulling the front panel up from the rear case.

• The iSclack is designed to safely open your iPhone just enough to carve up the pieces, just not enough to damage any cables.

• Skin the two suction cups off your iPhone.

• Skip the next three steps and continue on Stride 9.

• Press a suction cup onto the screen, just to a higher place the home button.

• Exist sure the cup is completely on the screen to become a tight seal.

• If you're opening an iPhone with cracked glass, neatly lay a couple strips of packing tape across the front and squeeze out as many bubbling as you lot can. This volition give the suction cup a surface to catch, and minimize the spread of broken glass.

• Make certain the suction cup is firmly attached to the front panel associates.

• While belongings the iPhone down with one hand, pull up on the suction cup to slightly divide the front panel assembly from the rear case.

• Take your time and apply firm, constant force. The screen is a much tighter fit than most devices.

• With a plastic opening tool, begin to gently pry the rear case down, away from the screen, while yous pull up with the suction cup.

• There are several clips attaching the forepart panel assembly to the rear case, then you may need to use a combination of the suction cup and plastic opening tool to costless the front panel assembly.

• Proceed to pry up around the sides of the front panel associates, detaching the clips along the left and right side.

• Do not effort to completely remove the front console associates from the rear instance, equally at that place are several ribbon cables still attached at the top of the iPhone.

• One time the clips have been released on the bottom and sides of the forepart panel associates, pull the bottom of the assembly abroad from the rear instance.

• Open the display to about a 90º angle, and lean it against something to keep it propped up while you're working on the phone.

• Add a rubber band to keep the display securely in place while you work. This prevents undue strain on the brandish cables.

• Remove the following two screws securing the metal battery connector bracket to the logic lath:

• One 1.8 mm Phillips screw

• 1 one.6 mm Phillips screw

• Remove the metal battery connector bracket from the iPhone.

• Employ a plastic opening tool to gently pry the bombardment connector upwards from its socket on the logic board.

• Be careful not to dislodge the minor surface-mounted components surrounding the socket.

• Be very careful to just pry up on the battery connector itself and not the socket on the logic board. If yous pry upwardly on the logic board socket or the board itself, yous may destroy the socket or damage nearby components on the board.

• Remove the post-obit screws securing the front end console assembly cablevision bracket to the logic board:

• Two 1.2 mm Phillips screws

• One 1.half dozen mm Phillips screw

• This screw tends to non be attracted to a magnetized screwdriver. Take care not to lose it when removing, and brand sure it gets back into the right place—a magnetized screw may interfere with the compass.

• Elevator the display cable bracket toward the battery to unhook it, and remove it from the iPhone.

• During reassembly, clip the left-hand hooks nether the logic board and lower the bracket towards the outside of the telephone.

• Make certain the battery is asunder earlier you disconnect or reconnect the cables in this stride.

• Apply a plastic opening tool or a fingernail to disconnect the three front panel assembly cables:

• Front-facing photographic camera and sensor cable

• LCD cable

• Digitizer cable

• When reassembling your phone, the LCD cablevision may popular off the connector. This can crusade white lines, or nada at all to appear when powering your phone back on. If that happens, simply reconnect the cablevision and power wheel your phone. The best mode to power wheel your phone is to disconnect and reconnect the battery.

• Remove the front console assembly from the rear case.

• Employ the exposed clear plastic pull tab to peel the battery off the adhesive securing it to the iPhone.

• If yous are having trouble peeling the battery upward or if the tab breaks, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery.

• Expect about i minute for the alcohol solution to weaken the agglutinative. Utilise an opening tool to gently lift the battery by its edge.

• Don't try to forcefully lever the bombardment out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.

• If at that place's any booze solution remaining in the telephone, advisedly wipe information technology off or permit it to air dry before installing your new battery.

• If you still take trouble peeling the battery up, use an iOpener or pilus dryer to heat the rear case of the iPhone and soften the agglutinative.

• Overheating the iPhone may ignite the bombardment.

• Use the plastic opening tool to gently pry the battery upwardly, only at the outside edge of the phone. Prying anywhere else, especially nearly the logic lath, may result in damage to the logic lath.

• If the battery doesn't pry easily out of the case, apply a few more drops of isopropyl alcohol.

• Pry gently and evenly to avert deforming the battery. A aptitude battery can exist a fire hazard.

• Practise not pry at the superlative portion of the battery, you chance severing the volume control cables.

• Remove the battery.

• If your replacement bombardment came in a plastic sleeve, remove information technology earlier installation by pulling it away from the the ribbon cable.

• Before you lot adhere the replacement battery, temporarily reconnect the battery connector to the motherboard socket. This ensures that the battery is properly aligned in its recess.

• Attach the bombardment, disconnect it, and go on reassembling your device.

• During reassembly, make sure the battery is seated firmly against the rear example. This will prevent whatsoever impairment to other components when reinstalling the forepart console associates.

• Perform a difficult reset after reassembly. This can prevent several issues and simplify troubleshooting.

Determination

Compare your new replacement function to the original part—y'all may demand to transfer remaining components or remove adhesive backings from the new part earlier installing.

To reassemble your device, follow the in a higher place steps in reverse order.

Accept your e-waste to an R2 or eastward-Stewards certified recycler.

Repair didn't go as planned? Cheque out our Answers community for troubleshooting assistance.

Attached Documents

Squad

Embed this guide

Choose a size and copy the lawmaking below to embed this guide as a small widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/How+to+replace+your+iPhone+5+battery/10587

Posted by: friendhintailging.blogspot.com

Share this post